IOP760 Ethernet/UART to Wi-Fi Converter with Modbus RTU Support
Wireless converter linking Ethernet, UART and Wi-Fi with dual-band 802.11a/b/g/n/ac uplink, two LAN ports and RS-232/485 Modbus RTU support for M2M links.
- Wi-Fi uplink or Ethernet WAN connection, with roaming to a stronger access point when signal strength falls below the threshold
- IEEE 802.11a/b/g/n/ac Wi-Fi with dual-band 2.4/5 GHz operation and up to 300 Mbps (2.4 GHz) or 866 Mbps (5 GHz) data rate
- One RS-232/485 port (RJ12) for Modbus RTU devices, with baud rates up to 230400 bps on RS-485
- Two RJ45 Fast Ethernet LAN ports for linking local Ethernet devices
- One digital input (wet contact) and one relay output (30V / 1A) for device triggering or event reporting
- Up to 10 clients in AP mode, with WEP, WPA, WPA2 and PSK encryption
5 755,23 kr per stk.
| 1–9 stk. | 5 755,23 kr | |
|---|---|---|
| 10–30 stk. | 5 578,62 kr | −3 % |
| 31+ stk. | 5 464,35 kr | −5 % |
Produktinformasjon "IOP760 Ethernet/UART to Wi-Fi Converter with Modbus RTU Support"
The IOP760 CR is a wireless converter for machine-to-machine links. It moves data between Wi-Fi, Ethernet and a serial UART port, so serial or Ethernet devices can be reached over a wireless network. Serial data can be sent transparently or wrapped in Modbus protocol.
The Wi-Fi side supports IEEE 802.11a/b/g/n/ac and dual-band 2.4/5 GHz operation, and can run as a Wi-Fi uplink or as a multi-mode access point. If the signal drops below a set threshold, the unit can roam to a stronger access point. Two LAN ports allow local Ethernet devices to share the same link, and a single RS-232/485 port with RJ12 connector covers serial devices, with a 1-channel digital input and a 1-channel relay output for triggering or event reporting.
The metal housing mounts on a DIN rail or bracket and operates from +9~ 48 VDC. The source lists this ordering code as Asia-only and notes that it will be phased out.
Applications
- Wireless machine-to-machine (M2M) communication
- Wireless connection of Modbus RTU serial devices
- Connecting local Ethernet devices over a Wi-Fi link
- Device triggering and event reporting via digital input and relay output
| Product type: | Wi-Fi Converter |
|---|---|
| Interface: | Ethernet, UART, Wi-Fi |
| Protocol: | Modbus RTU |
| Digital inputs: | 1 |
| Relay outputs: | 1 |
| Ports: | 3 |
| Power input: | +9~ 48 VDC |
| Operating temperature: | -20 ~ 60 °C |
| Mounting: | DIN-rail, bracket |
| Housing: | Metal |
Spesifikasjoner
| Wi-Fi | |
|---|---|
| Transmission Distance (LoS) | 50 meters (LOS) |
| Standard | IEEE 802.11a/b/g/n/ac |
| Encryption | WEP / WPA / WPA2 / WPA-PSK / WPA2-PSK |
| Data Transmission Rate | 2.4 GHz:300 Mbps(MIMO 2T2R) 5 GHz:866 Mbps(MIMO 2T2R) |
| Client | Max. 10 Clients (AP mode) |
| Channels | 2.4 GHz:1~11 5 GHz:36/40/44/48;149/153/157/161/165 |
| Antenna | 5 dBi 2.4/5 GHz |
| Digital Input | |
| Channels | 1 |
| Type | Wet Contact |
| ON Voltage Level | 3.3 ~ 30 VDC |
| OFF Voltage Level | 3 VDC Max. |
| Relay Output | |
| Channels | 1 |
| Contact Rating | 30V / 1A |
| Ethernet | |
| Ports | 2 x RJ45 FE |
| COM Ports | |
| Ports | 1 x RJ12( RS-232/RS-485) |
| Baud Rate | RS-232: 9600 / 19200 / 38400 / 57600 / 115200 RS-485: 9600 / 19200 / 38400 / 57600 / 115200 / 230400 / 460800 |
| Data Bit | 8/7 |
| Power | |
| Input Range | +9~ 48 VDC |
| Mechanical | |
| Dimensions (mm) | 31 x 99 x 131 (W x L x H)(without Mounting kit) 31 x 108 x 131 (W x L x H)(with DIN Rail kit) 167 x 99 x 39 (W x L x H)(with Bracket kit) |
| Installation | DIN-Rail Bracket |
| Environment | |
| Operating Temperature | -20 ℃ ~ 60 ℃ |
| Storage Temperature | -40 ℃ ~ 85 ℃ |
| Humidity | 10% ~ 95% (non-condensing) |
Spesifikasjoner som oppgitt av produsenten. Med forbehold om endringer.
Nedlastinger
Logg inn