Bevegelseskontrollkort

The PCIe-ENCODER300 is a PCI Express x1 motion input card for PC-based and remote motion systems. It provides three independent encoder channels, and each axis has its own true 32-bit counter capable of counting up to 4 MHz.Each axis can be set to Quadrant, CW/CCW or PULSE/DIR counting mode. Counters can be cleared by register command, by the index (C channel) signal once per revolution, or by an external hardware reset input (HR1 to HR6). The HR1 to HR6 inputs can also be read as digital inputs when not used for reset.6 digital inputs, optically isolated at 2500 Vrms8 digital outputs, optically isolated at 2500 Vrms68-pin SCSI-II female connectorDevice drivers and function libraries are supplied for DOS, Windows 7 and Windows XP/2000, and the card is listed for Windows 11 and Windows 10 in the software specification. An operating temperature range of 0 ~ +60 °C suits typical cabinet and industrial PC environments.ApplicationsSemiconductor ManufacturingComponent InspectionManufacturing Quality ControlFood and Beverage InspectionMicroscopy and Medical ImagingBiometrics ApplicationsX-Y-Z TableFix-pitch Stamping MachineryTransfer MachinerySpinnerLoad/Unload

The PCIe-ENCODER600 CR is a PCI Express x1 motion input card for PC-based systems that need to read six encoder axes at once. Each axis has its own true 32-bit counter, with a maximum encoder counting rate of 4 MHz.Counting can be set to Quadrant, CW/CCW or PULSE/DIR mode, so the card suits a range of encoder signal formats. The counters can be cleared by software register command, by the C channel index pulse once per revolution, or by external hardware reset inputs HR1 to HR6. The HR pins can also be used as digital inputs when reset is not required.Eight digital outputs are provided, and the digital I/O is isolated with 2500 Vrms photo-couplers to keep high voltages away from the host system. Device drivers and function libraries are supplied for DOS, Windows and Linux, with LabVIEW support.ApplicationsSemiconductor manufacturingComponent inspectionManufacturing quality controlFood and beverage inspectionMicroscopy and medical imagingBiometrics applicationsX-Y-Z tablesFix-pitch stamping machineryTransfer machinerySpinnersLoad/unload systems

The PCIe-PS400 CR is a 4-axis stepping and pulse-type servo motor control card for industrial PCs with a PCI Express bus. It suits general-purpose motion control, with a maximum pulse output rate of 4 MHz on each axis and CW/CCW or PULSE/DIR output modes.Most motion functions, including linear and circular interpolation, T/S-curve acceleration and deceleration, synchronous actions and automatic homing, run on a dedicated motion ASIC, which keeps processor load low. Motion status and other I/O cards in the same IPC can still be monitored while the motors are driven, and one or more cards can be used in a single IPC.Software support includes the EzGo Utility and an SDK for LabVIEW 5.0 to 8.x, with OS support for Windows 7/10 (32/64-bit) and Windows XP/2000 (32-bit). The card uses a 68-pin SCSI-II connector and a rated consumption of +12 V at 200 mA and +3.3 V at 500 mA.ApplicationsSemiconductor ManufacturingComponent InspectionManufacturing Quality ControlFood and Beverage InspectionMicroscopy and Medical ImagingBiometrics ApplicationsX-Y-Z TableFix-pitch Stamping MachineryTransfer MachinerySpinnerLoad/Unload

The PISO-ENCODER300U is a Universal PCI card for motion and position feedback in PC-based automation. It provides three independent encoder axes, each with a true 32-bit counter that accepts encoder rates of up to 4 MHz. A third-order internal digital filter helps keep counts reliable on noisy signal lines.Each axis can be set to Quadrant, CW/CCW or PULSE/DIR counting mode. Counters can be reset through a programmable register command, by the index pulse on the C channel at each revolution, or through the external hardware reset pins HR1 to HR6, which can also serve as digital inputs. The card adds eight digital outputs, isolated by 2500 Vrms photo-couplers to protect the host system from high voltages.The CR ordering code includes the CA-SC68 SCSI-II 68-pin male connector with solder-type terminals and cover. Device drivers and function libraries are provided for DOS, Windows 7 and Windows XP/2000.ApplicationsSemiconductor manufacturingComponent inspectionManufacturing quality controlFood and beverage inspectionMicroscopy and medical imagingBiometrics applicationsX-Y-Z tablesFix-pitch stamping machineryTransfer machinerySpinnersLoad/unload systems

The PISO-ENCODER600U is a universal PCI bus card for reading six encoder axes from a single PC slot. Each axis has its own true 32-bit counter, with counting at up to 4 MHz, which suits engineers tracking several motion axes at once.Counting can be set to quadrant, CW/CCW or PULSE/DIR mode, and a third-order internal digital filter is built in. Counters can be cleared by a programmable register reset, by the C channel index signal once per revolution, or by the external HR1 to HR6 hardware reset pins, which can also be used as digital inputs.Eight digital outputs are isolated with 2500 Vrms photo-couplers. The CR ordering code includes a CA-SC68 SCSI-II 68-pin male solder-type connector with cover. Software support covers Windows 11, Windows 7/10 and XP/2000, plus DOS and Linux 2.6 through the SDK, with LabVIEW 8.5 and above.ApplicationsSemiconductor ManufacturingComponent InspectionManufacturing Quality ControlFood and Beverage InspectionMicroscopy and Medical ImagingBiometrics ApplicationsX-Y-Z TableFix-pitch Stamping MachineryTransfer MachinerySpinnerLoad/Unload

The PISO-PS200 is a PCI motion control card for independent two-axis control of stepping and pulse-type servo drives. Each axis outputs pulses at up to 4 MHz and reads a 32-bit encoder counter, with hand wheel and jog operation and programmable automatic homing and software limits. It suits machines that need precise positioning on two axes from a single PC.Interpolation and speed profiling run on the card itself. Linear and circular 2-axis interpolation, continuous interpolation and programmable T/S-curve acceleration and deceleration are included. The onboard FRnet Master expands remote I/O by up to 128 DI and 128 DO over a two-wire interface, scanned automatically within 2.88 ms.The card is supported on Windows 7/10 (32/64-bit) and Windows XP/2000 (32-bit) and ships with the EzGo Utility. It requires a 5 V PCI bus and draws +5 V at 500 mA. The rated operating temperature range is -20 ~ +75°C.ApplicationsSemiconductor ManufacturingComponent InspectionManufacturing Quality ControlFood and Beverage InspectionMicroscopy and Medical ImagingBiometrics ApplicationsX-Y-Z TableFix-pitch Stamping MachineryTransfer MachinerySpinnerLoad/Unload

The PISO-PS300U CR is a universal PCI card for controlling three axes of stepper or servo motors through pulse command outputs. An embedded CPU carries out the motion commands sent from the host PC and returns position and status data, with buffering on both paths. This suits Windows-based machines where the PC handles the application and the card takes care of the pulse timing.Motion features include linear and circular interpolation across axes, a programmable T-curve speed profile and a programmable DDA cycle. Encoder inputs support A/B phase, CW/CCW and PULSE/DIR modes, with a 32-bit counter. A hardware emergency stop and mechanical switch inputs for home and travel limits are included, alongside 8 digital inputs and 7 digital outputs with 2500 Vrms optical isolation.The CR ordering code includes a CA-9-2502 D-Sub cable (0.2 m, 9-pin male to 25-pin female) and three D-Sub connectors with plastic covers (CA-PC09F, CA-PC09M and CA-PC25M). Drivers and function libraries are provided for DOS, Windows XP/2000 and Windows 7 (32-bit only).ApplicationsSemiconductor manufacturingComponent inspectionManufacturing quality controlFood and beverage inspectionMicroscopy and medical imagingBiometrics applicationsX-Y-Z tablesFix-pitch stamping machineryTransfer machinerySpinner and load/unload systems

The PISO-PS400U is a 4-axis pulse-type motion control card for industrial PCs with a universal PCI bus, suited to general-purpose motion control. Each axis outputs pulses at up to 4 MHz and reads a 32-bit encoder counter, so it can drive stepping or servo drives from a single card.Most motion functions, including interpolation, T/S-curve acceleration and deceleration, automatic homing and synchronous actions, run in the motion ASIC rather than the host processor. Motion status, FRnet I/O and other I/O cards in the same PC can still be monitored while motors are driven, and several cards can share one PC because of the low CPU loading.The U variant is the universal PCI version, supporting 3.3 V and 5 V PCI slots. The FRnet master expands the system with up to 128 digital inputs and 128 digital outputs, scanned automatically within 2.88 ms, and ICP DAS supplies functions and examples that reduce the programming effort required.ApplicationsSemiconductor manufacturingComponent inspectionManufacturing quality controlFood and beverage inspectionMicroscopy and medical imagingBiometrics applicationsX-Y-Z tablesFix-pitch stamping machineryTransfer machinerySpinnersLoad/unload systems

PISO-PS600 is a PCI motion controller for engineers who need to coordinate up to six axes from a PC. A DSP and FPGA combination handles pulse output, encoder feedback and interpolation on the card, so the host is free to run the application logic. Each axis can run in full-closed or semi-closed loop operation, with incremental or absolute positioning.The card suits machines that need fast trajectory control, such as X-Y-Z tables, stamping and transfer equipment. Motion profiles use programmable T/S-curve acceleration and deceleration, and speed and position can be changed while a move is in progress. Linear interpolation across two to six axes, circular interpolation across two to three axes and helical interpolation on three axes are all supported.An onboard FRnet master port extends the digital I/O by up to 128 inputs and 128 outputs over a two-wire link, scanned automatically. Latch inputs, position compare outputs, manual pulse generator and jog functions complete the set of motion I/O on the card.ApplicationsSemiconductor ManufacturingComponent InspectionManufacturing Quality ControlFood and Beverage InspectionMicroscopy and Medical ImagingBiometrics ApplicationsX-Y-Z TableFix-pitch Stamping MachineryTransfer MachinerySpinnerLoad/Unload

The PMDK is a DSP-based motion control card for the PCI bus, intended for engineers developing professional motion control applications. It fits any IPC with a 5 V PCI bus and combines a high-speed DSP and an FPGA with I/O buffering circuitry, so it can cover pulse, analogue and digital I/O in a single card.Motion functions include multi-axis linear and circular interpolation with acceleration and deceleration processing, plus synchronous actions set up through programming. Because the DSP runs on a real-time kernel, motion status and I/O status can be monitored during operation, and the low CPU loading means more than one card can be used in the same IPC.Remote expansion is available through a single two-wire FRnet port, which supports up to 128 DI and 128 DO channels. Sample software for motion and signal processing tasks is included to shorten development time for custom programs.ApplicationsSemiconductor manufacturingComponent inspectionManufacturing quality controlFood and beverage inspectionMicroscopy and medical imagingBiometrics applicationsX-Y-Z tablesFix-pitch stamping machineryTransfer machinerySpinnersLoad/unload systems