NS-200AFT-T Media Converter, 10/100Base-TX to 100Base-FX Multi-Mode ST
Industrial media converter linking one 10/100Base-TX RJ-45 port to a 100Base-FX multi-mode ST fibre link, with a wide 12 to 48 VDC input and DIN-rail mounting for -30 ~ +75 °C environments.
- Single 10/100Base-TX RJ-45 port to single 100Base-FX multi-mode ST fibre port
- Auto negotiation at 10/100 Mbps with automatic MDI/MDI-X for plug-and-play connection
- Store-and-forward processing with wire-speed switching and IEEE 802.3x flow control
- Fibre support for 50/125, 62.5/125 or 100/140 μm cable, with 2 km full-duplex distance (62.5/125 μm recommended)
- Wide input range of +12 VDC to +48 VDC with reverse polarity protection
- Operating temperature -30 °C ~ +75 °C with 1500 Vrms (1 minute) Ethernet isolation
1 755,66 kr per stk.
| 1–9 stk. | 1 755,66 kr | |
|---|---|---|
| 10–30 stk. | 1 703,71 kr | −3 % |
| 31+ stk. | 1 662,16 kr | −5 % |
Produktinformasjon "NS-200AFT-T Media Converter, 10/100Base-TX to 100Base-FX Multi-Mode ST"
NS-200AFT-T bridges a copper Ethernet segment and a multi-mode fibre link. The RJ-45 port runs at 10 or 100 Mbps with auto negotiation and automatic MDI/MDI-X, so it can be connected to a switch or a device without choosing a crossover cable. The fibre side uses a 100Base-FX multi-mode ST connector, suited to extending an Ethernet connection across the distances covered by the fibre specification.
The converter uses store-and-forward processing with wire-speed switching and supports IEEE 802.3, 802.3u and 802.3x, including flow control. Reverse polarity protection is fitted on the power input, which accepts +12 VDC to +48 VDC (non-isolated). Power consumption is 0.12 A at 24 VDC.
The plastic housing is slim enough for DIN-rail mounting and is rated for an operating temperature of -30 °C ~ +75 °C, with a storage range of -30 °C ~ +85 °C. Status LEDs show power, 10M and 100M speed, link/activity and the fibre duplex state. The product is listed with CE, UKCA, FCC, RoHS and WEEE certifications.
Applications
- Extending 10/100Base-TX Ethernet connections over 100Base-FX multi-mode fibre in industrial installations
- Connecting copper-based Ethernet devices to a fibre backbone in cabinets with a DIN-rail footprint
| Product type: | Media Converter |
|---|---|
| Interface: | 10/100Base-TX, 100Base-FX |
| Ports: | 1 x RJ-45, 1 x ST |
| Isolation: | 1500 Vrms (1 min) |
| Power input: | +12 ~ +48 VDC |
| Operating temperature: | -30 ~ +75 °C |
| Mounting: | DIN-rail |
| Housing: | Plastic |
Spesifikasjoner
| LED Indicators | |
|---|---|
| Status | PWR, 10M, 100M, Link/Act, Full duplex/Half duplex(Fiber Port) |
| Ethernet | |
| Ports | 1 x RJ-45, 10/100Base-TX |
| Standards | IEEE 802.3, 802.3u, 802.3x |
| Processing Type | Store & forward, wire speed switching |
| MAC Table | 1024 |
| Memory Bandwidth | 1.4 Gbps |
| Frame Buffer Memory | 256 Kbit |
| Flow Control | IEEE 802.3x flow control, back pressure flow control |
| Isolation | 1500 Vrms 1 minute |
| Fiber | |
| Ports | 1 x 100 Base-FX, ST connector |
| Mode | Multi-Mode |
| Fiber Cable | 50/125, 62.5/125 or 100/140 μm |
| Distance | 2 km, (62.5/125 μm recommended) for full duplex |
| Wavelength | 1300 or 1310nm |
| TX Output | -20 dBm Min. -14 dBm Max. |
| RX Sensitivity | -32 dBm |
| RX Overload | -8 dBm |
| Budget | 12 dBm |
| Power | |
| Reverse Polarity Protection | Yes |
| Input Range | +12 VDC ~ +48 VDC (Non-isolation) |
| Consumption | 0.12 A @ 24 VDC |
| Mechanical | |
| Casing | Plastic |
| Dimensions (mm) | 33 x 107 x 78 (W x L x H) |
| Installation | DIN-Rail Mounting |
| Environment | |
| Operating Temperature | -30 °C ~ +75 °C |
| Storage Temperature | -30 °C ~ +85 °C |
| Humidity | 10% ~ 90% RH, non-condensing |
Spesifikasjoner som oppgitt av produsenten. Med forbehold om endringer.
Nedlastinger
Logg inn